Buy the whole cabinet the most expensive number of cabinets, and some consumers pay attention to the appearance when buying a cabinet, but they ignore the "memory", which is the cabinet plate of the kitchen cabinet, and its quality often affects the quality of the cabinet. Affects future use.
Usually the box board is made of two materials, particle board and medium density board. Most consumers are not aware of the difference between the two materials and the good ring. According to the degree of excellent performance, they should be imported particleboard, particle board and medium density board produced by domestic manufacturers with imported equipment, and the second housing board should be domestic. Small factory production of particleboard.
Particleboard: good overall performance
The middle layer of the particle board is made of long-fiber wood, with finely-organized wood fibers on both sides and pressed into a board. As the particle board's bending performance is better than the MDF is the main material of the current box.
Recently, almost all European and American cabinet factories use particleboard. Imported particleboard meets the highest European E1 environmental standards. The formaldehyde content is very low, the molecular structure is tight, and the bending strength is high. More than 50% of the cabinets use green moisture-proof agents. Plates, such particleboard without any change in the general wet conditions, the overall performance can be said to be better than the density plate. At present, several large domestic manufacturers can produce products with a compact molecular structure and high flexural strength due to the use of a full set of imported equipment (with an investment of over 200 million yuan). Since the plate is mainly composed of larger wood fibers (compared to density plates), even if it is immersed in water, its expansion rate is only 8% to 10% and it does not expand as much as the density plate. In general, if the surface decoration surface is imported from Germany, most of them are produced by large factories and used for high-end furniture, so there are fewer problems.
MDF: General moisture resistance
MDF is formed by pressing wood powder and has a good surface flatness. Therefore, when the surface needs boring and milling, and the surface to be glued is soft (such as stencil blister), MDF is often used. Ensure that the surface after the film is flat. However, due to the fact that the raw materials are all very fine wood powder, from the perspective of moisture resistance, if a medium density board is soaked in water, it will expand like bread; while the particle board is soaked in water, because of the presence of long wood fiber in the particle board, more The structure of the wood is preserved, so the expansion will not expand when it is to a certain extent. Therefore, the cabinet company does not have a certain degree of reason to use the medium density board as a box material more generally.
Small particleboard produced by the factory: not environmentally friendly
Some domestic small factories can only produce some common common white boards and eucalyptus wood boards. Because of the backward equipment and production process, the boards produced are poor in load-bearing capacity, bending resistance, and deformation strength. The cabinets that are made can easily be loosened after being fastened. , Loosening after the strength is insufficient, rapid expansion after encountering water. And the high content of formaldehyde, more than a few times the national standard, great harm to the human body. It is the quality of this type of board that has tainted the reputation of particleboard and has led consumers to mistakenly believe that the quality of the board is inferior.
Buy materials Formaldehyde decoration company Decorative furniture
Holland Wire Mesh is made with plain steel wire welded together in square opening, then going through the hot dipped zinc coating process.
Application: Suitable product for constructing animal cages, enclosure works, fabricating of wire containers and baskets, grills, partitions, machine protection fences, gratings and Other construction applications.
Hot dipped zinc Coated Welded Wire Mesh is made in accordance to English Standard normally in regard to the production and zinc coating. The finished welded mesh offer flat and uniform surface, firm structure, good integrity. It offers the most excellent anti-corrosion resistance among all the steel wire mesh products, it is also the most versatile wire mesh due to its wide application in different fields.
Features and Application:
It is very popular in breeding industry: Can be made into various animal cages or fences for breeding with its excellent anti-corrosion property. The zinc coating offers a kind of decorative outlook with its flat surface.
With first-class anti-corrosion property, it is widely used in mine sieving industries as sieving screen. The low carbon steel wire for making of hot-dipped Welded Wire Mesh offers flexibility that can be made in many further fabrication applications.
We supply hot dipped galvanized welded wire mesh in the following forms:In rolls;In panels.
Holland Wire Mesh
Holland Wire Mesh,Holland Welded Wire Mesh,Welded Wire Mesh For Holland
Hebei Giant Metal Technology Co., Ltd. , http://www.358fencing.com