To meet the needs of anti-glare lighting for railway tunnels, highway bridges, public venues and various production enterprises, the newly developed NSC9720 anti-glare way lamps are widely used in tunnels, roads and bridges, large-scale facilities, factory areas, and stations. For road, channel flood lighting.
Protection angle design and mirror coating technology are used to achieve anti-glare effect, which can effectively reduce the irritation to eyes of operators and constructors.
To avoid discomfort and fatigue, choose a gas discharge light source.
High luminous efficiency, long life, power factor greater than 0.9, good light transmission, and long life of 10,000 hours.
The special surface coating and sealing treatment ensure that the lamps will never corrode in humid, high temperature and Other harsh environments and never rust.
Multiple shock-proof structure design and high-strength alloy casing ensure long-term safety in high-frequency vibrations such as roadbed rails and bridge tunnels.
Seat type, ceiling type and wall-mounted installation methods, irradiation angle can be adjusted in the upper and lower 180 large range according to the needs of the environment.
Instructions
1, according to the scene environment and lighting needs, determine the installation location and mode of the lamp after the fixed installation, according to the lamp to the 220V power contact point distance, prepare the appropriate length of cable.
2. Unscrew the two butterfly bolts that fix the front cover on the upper part of the lamp to open the front cover, and insert one end of the prepared cable into the lamp cavity through the compression nut of the introduction device. According to the polarity marked on the terminal block, connect and reconnect. Screw in the tightening nut of the introduction device.
3, close the front cover, tighten the top two butterfly bolts, and then connect the other end of the cable to 220V power supply for lighting.
4. When multiple lights are used in parallel, the cable is introduced from another lead-in device according to the above method and then connected with other luminaires. When a single light is used, the idle lead-in device is plugged with a plug.
5. Loosen the fixing screws on both sides of the bracket to adjust the lighting angle of the fixture within the range of up and down 15.
6. The inside of the lamp chamber is equipped with a support rod, which can be supported as needed after the lamp cover is opened.
Precautions
1. When the light is transported, it should be installed in the equipped carton and be equipped with foam shock absorption.
2. When used, there is a certain temperature rise on the surface of the lamp, which is a normal phenomenon; the center temperature of the transparent part is relatively high and must not be touched.
3, when replacing the bulb, try to use the same type of bulb; if you change the bulb type or power, you should replace the matching ballast.
4. The temperature of the cable introduced into the lamp cavity should not be lower than 120°C (such as silicone rubber, PTFE cable, etc.).
caveat:
1, can not be directly installed on combustibles;
2. Replace any protective screen that has been cracked;
3, when installing and maintaining the lighting, you must first disconnect the power;
4, lamps must be reliably grounded.
Protection angle design and mirror coating technology are used to achieve anti-glare effect, which can effectively reduce the irritation to eyes of operators and constructors.
To avoid discomfort and fatigue, choose a gas discharge light source.
High luminous efficiency, long life, power factor greater than 0.9, good light transmission, and long life of 10,000 hours.
The special surface coating and sealing treatment ensure that the lamps will never corrode in humid, high temperature and Other harsh environments and never rust.
Multiple shock-proof structure design and high-strength alloy casing ensure long-term safety in high-frequency vibrations such as roadbed rails and bridge tunnels.
Seat type, ceiling type and wall-mounted installation methods, irradiation angle can be adjusted in the upper and lower 180 large range according to the needs of the environment.
Instructions
1, according to the scene environment and lighting needs, determine the installation location and mode of the lamp after the fixed installation, according to the lamp to the 220V power contact point distance, prepare the appropriate length of cable.
2. Unscrew the two butterfly bolts that fix the front cover on the upper part of the lamp to open the front cover, and insert one end of the prepared cable into the lamp cavity through the compression nut of the introduction device. According to the polarity marked on the terminal block, connect and reconnect. Screw in the tightening nut of the introduction device.
3, close the front cover, tighten the top two butterfly bolts, and then connect the other end of the cable to 220V power supply for lighting.
4. When multiple lights are used in parallel, the cable is introduced from another lead-in device according to the above method and then connected with other luminaires. When a single light is used, the idle lead-in device is plugged with a plug.
5. Loosen the fixing screws on both sides of the bracket to adjust the lighting angle of the fixture within the range of up and down 15.
6. The inside of the lamp chamber is equipped with a support rod, which can be supported as needed after the lamp cover is opened.
Precautions
1. When the light is transported, it should be installed in the equipped carton and be equipped with foam shock absorption.
2. When used, there is a certain temperature rise on the surface of the lamp, which is a normal phenomenon; the center temperature of the transparent part is relatively high and must not be touched.
3, when replacing the bulb, try to use the same type of bulb; if you change the bulb type or power, you should replace the matching ballast.
4. The temperature of the cable introduced into the lamp cavity should not be lower than 120°C (such as silicone rubber, PTFE cable, etc.).
caveat:
1, can not be directly installed on combustibles;
2. Replace any protective screen that has been cracked;
3, when installing and maintaining the lighting, you must first disconnect the power;
4, lamps must be reliably grounded.
Double Horizontal Wire Fencing is a robust form of fencing now often used in and around schools,colleges and commercial properties.It is usually galvanized and powder coated,the standard colors being green or black but can be powder coated in any color.Double Horizontal Wire Fence has the features of grid structure, beauty and practical, landscaping. In addition, Because of the double wire fencing features of easy transportation and installing without the limitations of special terrain. It is adjust to mountain, hillside and winding zones.
Double Horizontal Wire Fence
Double Horizontal Wire Fence,Horizontal Wire Fence,Galvanized Wire Fence,Welded Security Wire Fence
Hebei Giant Metal Technology Co., Ltd. , https://www.wiremesh.pl