First, dehumidifier maintenance switch method using industrial dehumidifiers should not be frequent switching. Do not turn on and off the dehumidifier often because the room humidity has reached the required value or higher than the required value, and the dehumidifier should be controlled to start and stop through the humidity controller. When the dehumidifier is not in use, turn off the power and unplug the power plug. If the dehumidifier stops for any reason (such as sudden power cut, artificial shutdown, etc.), since the dehumidifier does not have any time delay (delay time is about 3 minutes), the household dehumidifier can be turned on immediately after shutdown. , but it takes 3 minutes before it can run. However, for a dehumidifier without a time delay, the dehumidifier cannot be turned on immediately after shutdown. Be sure to turn on the dehumidifier again after about 3 minutes. Otherwise, the start-up current may be too large, the fuse may be burned, or even the compressor motor may be burned. In particular, pay attention to the effective use of timing functions. When sleeping and going out, use the timing function to run it only for the necessary time to save power.
Second, dehumidifier maintenance Humidity industrial dehumidifier operation should pay attention to carefully adjust the humidity, to avoid too high or too low. If every 2% lower, you can save about 10%. When the dehumidifier is running, try to open the doors and windows as little as possible. Frequent opening and closing of doors and windows will dehumidify the dehumidifier's cooling and dehumidifying effect and waste electricity. Especially in the summer, direct sunlight blocking the dehumidifier can save about 5%. In addition, the space with good sealing conditions is the most energy-efficient.
Third, the dehumidifier maintenance filter secret method In all household appliances, dehumidifier, air conditioning, dust pollution is the most serious, and dehumidifier cleaning is also the most easily overlooked. Some users use the dehumidifier for many years and never wash it until it fails. Dehumidifiers that have been repaired for a considerable part are prematurely damaged due to lack of cleaning and maintenance. Therefore, dehumidifiers are generally required to be cleaned and maintained before or during the fall season. Especially the maintenance of the filter. After removing the air filter, gently bounce it or use a vacuum cleaner to clean it. If the filter is dirty, use water or a neutral detergent to wash it, but do not use hot water above 50°C to avoid deformation. Do not use sponges for cleaning, otherwise it will damage the surface of the filter, rinse with clean water, dry in a cool place, do not dry in the sun or by the stove to dry, because that may cause deformation. After the dried air filter is installed back into the dehumidifier, the entire dehumidifier maintenance process is completed.
Fourth, dehumidifier maintenance components secret method In the daily dehumidifier operation, should pay attention to protect the condenser and the evaporator heat sink. Condenser and evaporator fins are made of 0.112 mm aluminum sheets that are inserted into a copper tube and then expanded to prevent them from colliding. If the fins are damaged, the dehumidifier's heat dissipation effect will be affected and the dehumidification efficiency will be reduced. In addition, we must also protect the refrigeration system. If parts of the refrigeration system or piping are damaged, the refrigerant leaks and the dehumidifier cannot be cooled. Remove the movement each year and inject suitable lubricant into the fan motor bearing. The refrigeration system does not need to be treated. Just remove the dirt from the surface. Also, the dehumidifier must be properly selected for the fuse (fuse). Select the fuse size according to the rated current indicated in the product manual. If the size is too large, the insurance function cannot be used. If it is too small, it will often break.
Second, dehumidifier maintenance Humidity industrial dehumidifier operation should pay attention to carefully adjust the humidity, to avoid too high or too low. If every 2% lower, you can save about 10%. When the dehumidifier is running, try to open the doors and windows as little as possible. Frequent opening and closing of doors and windows will dehumidify the dehumidifier's cooling and dehumidifying effect and waste electricity. Especially in the summer, direct sunlight blocking the dehumidifier can save about 5%. In addition, the space with good sealing conditions is the most energy-efficient.
Third, the dehumidifier maintenance filter secret method In all household appliances, dehumidifier, air conditioning, dust pollution is the most serious, and dehumidifier cleaning is also the most easily overlooked. Some users use the dehumidifier for many years and never wash it until it fails. Dehumidifiers that have been repaired for a considerable part are prematurely damaged due to lack of cleaning and maintenance. Therefore, dehumidifiers are generally required to be cleaned and maintained before or during the fall season. Especially the maintenance of the filter. After removing the air filter, gently bounce it or use a vacuum cleaner to clean it. If the filter is dirty, use water or a neutral detergent to wash it, but do not use hot water above 50°C to avoid deformation. Do not use sponges for cleaning, otherwise it will damage the surface of the filter, rinse with clean water, dry in a cool place, do not dry in the sun or by the stove to dry, because that may cause deformation. After the dried air filter is installed back into the dehumidifier, the entire dehumidifier maintenance process is completed.
Fourth, dehumidifier maintenance components secret method In the daily dehumidifier operation, should pay attention to protect the condenser and the evaporator heat sink. Condenser and evaporator fins are made of 0.112 mm aluminum sheets that are inserted into a copper tube and then expanded to prevent them from colliding. If the fins are damaged, the dehumidifier's heat dissipation effect will be affected and the dehumidification efficiency will be reduced. In addition, we must also protect the refrigeration system. If parts of the refrigeration system or piping are damaged, the refrigerant leaks and the dehumidifier cannot be cooled. Remove the movement each year and inject suitable lubricant into the fan motor bearing. The refrigeration system does not need to be treated. Just remove the dirt from the surface. Also, the dehumidifier must be properly selected for the fuse (fuse). Select the fuse size according to the rated current indicated in the product manual. If the size is too large, the insurance function cannot be used. If it is too small, it will often break.
Sodium Methoxide,Sodium Methoxide Powder,Sodium Methoxide 20%,Solid Sodium Methoxide 124-41-4
ShanDong YingLang Chemical Co.,LTD , https://www.sdylhgtrade.com