People's demands for quality of life are getting higher and higher, and more emphasis is placed on the living environment. At leisure weekends, walk to the park, bask in the sun and breathe fresh air. Parents take their children and play on the lawn. Naturally relaxing time, people forget about the hustle and bustle of urban life. We know that the lawn is very easy to damage, and most of the grass in the park is bare. At this time, there is an alternative—a fake turf. It is a good choice for lawns, such as kindergartens, school football courts, and other fake lawns. If there are conditions, you can get such a venue in the yard for children to play. Let's learn about the construction method of the fake lawn.
Before the fake turf enters the construction site, it is first cleared. To detect the flatness, slope and surface appearance of the foundation, repair measures and requirements are required to be repaired, and construction can be carried out only after the requirements are met;
The first step is to take the line (measurement), find out the center point of the site and two semi-circle centers, and then use the three positioning points to draw the ruler, determine the intersection of the site center line and the edge line, and then use the Pythagorean theorem to determine the site The exact position of the corners and lines, and then the position of each function point, line; and use the ink line or paint line to pop up.
The second step: move the turf into the field and spread it along the horizontal direction, and push it from one end of the vertical side to the other in turn. When spreading out, try to make the white line weaving on the turf at the position of the function line to reduce the cutting. Quantity;
Step 3: Cut out the white grass line that is woven on the outer edge of the turf and cannot be placed on the functional line. Place it on the side and set it aside. If the white line is woven, it must be manually cut into 12CM wide white strokes. line;
Step 4: Lay out 2-3 cm of the green turf at each seam and cut it from the center of the lap with a cutting blade to make the turf on both sides overlap as tightly as possible. Then use a paper knife to trim.
Step 5: Spread a 20 or 30 cm wide connection strip along the turf seam and place it under the turf so that the turf seam is as close as possible to the center of the connecting strip (if it gets wet by rain, it needs to dry Then, the universal glue is evenly smeared on the connecting belt with a squeegee, and the turf on both sides is put together, glued on the connecting belt, and beaten with a rubber hammer so as to make the bonding part tightly bonded. If the joint is straight after being straightened, a gap of 2-5 cm can be cut here and stretched toward the interface to ensure the appearance is beautiful;
Step 6: After the basic splicing of the turf is completed, pull the cable again to set the exact position of each function line and point, cut it with a knife, pull out the cut grass, put the connecting tape, and apply the glue to the original. The ready-to-use white grass line was put back and cemented, and then repeatedly beaten with a rubber hammer to make the connection part tightly adhered.
Step 7: After the turf paving is completed, the folded part of the turf needs to open with a knife, straighten the butt joints, remove the overlapped part, and cement. After all the turf has been bonded, it begins to be combed with a lawn mower: on the first pass, the grass roll of the whole field is combed up with a lawn mower.
There are many functions of fake turf, such as accidentally falling on the grass. The clothes are not particularly dirty. At the same time, they are not easily injured. The lawn is relatively clean. The game on the lawn is very convenient. No watering is needed, saving water resources.
Decoration construction knowledge
It is polyvinyl chloride (PVC) plastic with an excellent performance of the main Plasticizer.Compared with DOP, it has the advantages of heat resistance, cold resistance, low volatility, resistance to extraction, flexibility and electrical insulation.In the products show excellent durability, resistance to soapy water and low temperature flexibility.Because of its low volatility, the use of DOTP can fully meet the temperature requirements of wire and cable, can be widely used in 70 ℃ cable material (International Electrotechnical Commission IEC standards) and other soft PVC products.
Application:
DOTP addition to a large number of cable materials, PVC plasticizer, can also be used for the production of artificial leather film.In addition, has excellent compatibility, can also be used for acrylonitrile derivatives, polyvinyl butyral, nitrile rubber, nitrocellulose and other plasticizers.It can also be used in synthetic rubber plasticizers, paint additives, precision instruments, lubricants, lubricant additives, can also be used as paper softener.
Dioctyl Terephthalate,Dotp Cable Material,Dotp Pvc Plasticizer,Dotp Artificial Leather Membrane
Yucheng Jinhe Industrial Co.,Ltd , https://www.jinhetec.com