In the home decoration, hydropower installation can be regarded as a concealed project. Therefore, the installation of hydropower not only affects the economic loss, but also may cause some harm to human safety. Therefore, the standard size of hydropower installation should not be ignored. Therefore, the following Xiaobian introduces the standard size of hydropower installation and the standard of hydropower installation standards.
Hydroelectric installation standard size
1. Basin: 50cm Shower: 120cm Toilet: 20cm Wash basin: 40cm Mop pool: 75cm Washing machine: 120cm Electric water heater: 170cm Gas water heater: 130cm Bathtub: 35cm Mixing water valve between hot and cold water: 15cm.
2, kitchen equipment commonly used size: kitchen cabinet operating table height is 810-850mm; front and rear depth 500mm-600mm operating table to the end of the cabinet, the high size is about 550mm, too high is too low is not good; hanging cabinet shower outlet 1100mm.
3. Satellite TV sets the south-facing windows of the living room. The south-western direction is the direct broadcast of live Chinese (entertainment, national language) in Taiwan, and the southeast is CNN, BBC, HBO, and other full English programs. Place specific locations based on personal preferences.
4. The socket position is relatively consistent with the original socket position, generally 300-350mm.
5, dual control switch from the ground 850mm.
6, wall-mounted TV power supply distance 1100-1300mm height in 700 or so, too high to place items more laborious, thickness 300-350mm, range hood height above the stove is a standard height, in case of special circumstances, can be Properly change the distance from the bottom of the machine to 750mm.
Hydropower installation standard specification
1. The principle of wiring: horizontal and vertical. Use special PVC insulation pipe of Zhongcai PVC. The line pipe must be fixed in the line slot. When the line box and the line pipe are connected, the mother lock should be used. The straight pipe uses a pipe every 80 cm. Card, use a tube card every 20 centimeters around the corner.
2. In the upper part of the wall, the socket is vertically slotted upwards in the wall, and in the installation line of the decorative angle line at the top of the wall, if it is in the lower part of the wall, it shall be vertically slotted downwards to the bottom of the skirting board to be installed. Should be consistent, slot line and top straight line should be ejected after the control line in the wall, and then cut the wall surface with a cutting machine, slotted with a machine.
3, the use of financial PVC pipe, in the elbow when the spring is bent, not to use 90-degree elbow and three links (at this point we basically did not appear this type of situation), line installation must be sheathed Glue is used for connection. The edge of the casing shall be tightly closed. Flat and smooth. The right angle shall be cut at the inside of the corner. After the arc-shaped interface is cut at one side of the incision, it shall be bent and installed.
4, moderate depth of pipe teeth, no burr. The pipe joints are wrapped with raw material and wrapped 5-6 turns. The number of pipe twisted teeth is 5 teeth-6 teeth until the joint is tightened, and rotten teeth are not allowed to enter the pipe.
5, after the wire is installed into the casing, the wire fixing tool should be used. After fixing the wire inside the wall and the wall, the plaster is concealed.
6. It is strictly forbidden to lay the pipe directly under the composite panel. (At this point, we have not done a good job. We will communicate with the customer well later. The composite floor must be grooved.) The line pipe under the solid wood floor must be There are reinforcement measures.
7. It is forbidden to lay the line pipe on the kitchen or bathroom floor to prevent water from penetrating into the line pipe. (There must not be any wire tube on the floor of the bathroom. At this point we must strengthen the treatment.)
8. The wire that passes into the line pipe should not be more than 40% of the hole area of ​​the line pipe. There must be no joints in the pipe wires, and the wires of different purposes must not be mixed in one wire pipe.
9, the wire into the box must be guaranteed to leave a certain length, leaving 10 to 15 centimeters, leaving 100 centimeters of sound, wear a hose in order to switch the installation and maintenance of the socket.
10. The distance from the wall to the water pipe should be 1.5cm, left and right cold, and 15cm apart.
11. The parallel distance between the wire and the water pipe should not be less than 30 centimeters and cross over. The bridge distance should not be less than 10 centimeters.
12. Wire points and points must not have joints, and the dark lines in the ceiling must have flame-retardant tube protection.
13. After the acceptance of water and electricity is passed, the line slot and wall slot can be filled with dense 1:3 cement mortar (it should be divided into two levels of powder wall surface).
Editor's summary: The standards for hydropower installation standards and standards for hydropower installation are introduced here. I hope to help everyone. If you want to know more about yourself, you can follow the information on this site.
Hydroelectric installation hydropower installation standard size
Rectangular lock from the material divided rectangular stainless steel lock, Brass Padlock, Iron Padlock. It belongs beams, horizontal open padlock for theft tamper anti-cut. Widely used in factories, construction sites, companies and other large-scale security.
Various products of Rectangular Padlock, providing product images and basic parameters with each rectangular padlockand High Quality Rectanglar Brass Padlock Hardened Shackle (BX990); We are a professional Chinese manufacturer of rectangular padlock, and look forward to your cooperation!
Rectangular Good Quality Padlock
Rectangular Padlock,Rectangular Iron Padlock,Rectangular Security Padlock ,Brass Rectangular Padlock
Shengping Safety Protection Locks Manufacturer , https://www.chinajiuzhou.com