Generally good mahogany furniture is very expensive, and has a certain collection value. In the face of these expensive furniture, not only should you pay more attention when using it, but also have to do the corresponding maintenance work in order to ensure mahogany furniture. The service life can be longer, then Opel teaches you how to do the maintenance of mahogany furniture.
Mahogany furniture maintenance skills 1, resurrection moisturizing method Resurrection moisturizing method is mainly for long-term dry cracked mahogany furniture, the steps are as follows:
Step 1: After dusting and rubbing on the bottom of the furniture, use a humidifier to slightly humidify the cracked furniture. The humidity should be controlled at 8-12%, the humidification time should be controlled at about 6 hours, and the oil should be applied 12 hours after the humidification is completed. deal with.
Step 2: When oiling, special walnut oil for special mahogany should be used. It should be wiped with a small area first.
Maintenance skills of mahogany furniture Step 3: Do not wipe immediately after oiling, at least 48 hours, after the furniture is fully absorbed, wipe off the excess grease.
Step 4: Observe whether the furniture has a "re-softening phenomenon". If there is a softening phenomenon, dry the oil and add beeswax.
Step 5: The first time the beeswax should be thicker, the purpose is to control the oil and moisture.
Step 6: After resurrecting the furniture with the Revitalizing Moisturizing Method, you can gently wipe it with a dry towel every day, and apply a few drops of oil on the towel every other month for cleaning.
Maintenance of mahogany furniture O'Brien recommends this method to be tried in a small area after a small trial. It should be noted that when large-area trials are used for humidification, it is not possible to directly humidify the furniture.
2. The method of maintaining moisture is mainly used in the season when the weather is relatively dry in parts of the north. The steps are as follows:
Step 1: Focus on the furniture to be maintained in a room (mainly for furniture with chapped).
Step 2: Put a humidifier in the room where the furniture is concentrated. It should be noted that the humidifier should be humidified to a small amount and humidified once every 6 hours. The humidification time is 2 hours each time.
Maintenance of mahogany furniture Step 3: After a week of humidification, first apply a small amount of walnut oil to the furniture. After drying, dry it and wait for three days.
Step 4: After rubbing the oil for three days, apply a layer of moisturizing beeswax to control the moisture.
This method is recommended to try to use a small area in the bottom of the furniture, try to use it and then use it in large quantities.
3. Control of oil separation method The control oil separation method mainly focuses on the existing pulping of furniture, but the phenomenon of dry cracking occurs slowly in the pulping. The specific steps are as follows:
Maintenance skills of mahogany furniture Step 1: You can choose to remove dust, dirt and beeswax in a small area at the bottom of the furniture.
Step 2: Observe the week after the beeswax. If the furniture is “reflexive†and feels good, you can use this method on a large scale.
Source: GO Jiaju Furniture Network
Durostone Sheet or Synthetic stone is a kind of green and environment-friendly stone, which is composed of more than 95% natural stone powder, with a small amount of polyester and adhesives, mixed in vacuum, pressurized, and formed by vibration
Definition:
Durostone Sheet comes from the "stone kingdom" Italy, the English "composite stone".
According to the raw material into synthetic marble, synthetic quartz two kinds.
With the advantages of natural stone, large areas are paved with achromatic, environmental protection, high strength and complete variety.
Widely used in hotels, shopping malls, office buildings, public places, family walls, floors, etc.
Production process:
1. Collect stone materials from the quarry
2. Mix resin and stone powder and other materials in vacuum
3. Vacuum extruding ingredients
4. Leave about 10 days in the factory
Cut into large plates according to requirements
6. Measurement and polishing
7. Cut from the big board to the required panel
8. Waxing and corner handling and packaging
9, storage,
USES:
Main use in the wall of building adornment, ground, mesa, stair step.
The synthetic stone is used in the following areas:
1. The airport, the ground of the airport, part of the wall, the hallway, the bathroom table and the wall.
2. The public parts of the building and office buildings, such as the floor of the hall, the wall of the wall, the wall of the floor of each floor, the wall of the toilet, floor, mesa and elevator well.
3. Square, mall, these places can be used in large areas such as walls, floors, toilets, elevators and so on.
4, villa, with mesa main, in toilet also can often arrive, still have stair step.
5. Other places, such as public buildings, museums, exhibition centers, hospitals, schools, etc.
Advantages:
1, colorless difference, meet the market's natural marble directly from the mine mining, the slightly and the formation of mine decided the composition of natural stone and marble texture, so led to a number of natural stone texture of inconsistencies, and synthetic stone is to smash of natural marble, and processing and forming, so can very good control of color difference, this synthetic stone within a certain range can look without clear off color, this has the advantage of convenient and the laying of large area, as a whole to maintain consistent style.
2, environmental protection, natural marble is different according to the composition and properties, some deep color radioactive substances, and synthetic stone in choosing a natural stone powder can avoid these substances, so as to achieve no radiation environmental standards.
3, close to the natural stone texture, synthetic stone can be very close to the natural texture, color and so on some colors, the effect of synthetic stone laying large area can completely and natural stone.
4. Excellent performance, good absorption rate, and structure more closely than natural stone.
5. No crack, anti-fouling, easy to clean.
Specification: The thickness of sheet material can be produced from 3mm to 50mm,the usual specification of 3-50mm is 1150mm* 1250mm, It can also be customized according to requirements, and the width cannot exceed 1220mm, and the length is not limited
Color: Green ,can also be made another color, and the color order is 500KG.
Modified varieties: can be added to the fiberglass, copper powder and molybdenum disulphide to enhance the bar.
Add antistatic agent to the permanent antistatic electric bar, and the volume resistance value is between 6 to 9 power of 10.
Add flame retardant to flame retardant rod from UL 94V-0 to HB flame retardant grade. Other modification requirements are customized according to customer's actual use.
Product certification: most environmental certification reports and safety reports for raw materials, such as SGS report, CTI report, UL report, MSDS safety information, etc.
Durostone Sheet
Durostone Sheet,Durostone Sheet Price,Cheap Durostone Sheet
Dongguan Noegem Plastic Products Co.,Ltd , http://www.noegempLastic.com